Overview
| CODE | REASON | EFFECT |
| Fault Code: 3583 PID: SPN: 5031 FMI: 10/10 LAMP: Amber SRT: |
The aftertreatment outlet NOx sensor heater is unable to maintain its normal operating temperature.
|
None on performance. |
Circuit Description
The aftertreatment outlet NOx (nitrogen oxides) sensor is a smart device and communicates with the engine control module (ECM) via the J1939 data link. The aftertreatment outlet NOx sensor performs its own internal diagnostics and reports malfunctions back to the primary ECM using the J1939 data link. The NOx sensor is permanently attached to the NOx control module. They are serviced as a single component and can not be replaced individually. The aftertreatment outlet NOx sensor is used to measure the NOx emissions at the outlet of the aftertreatment system.
Component Location
The aftertreatment outlet NOx sensor location can vary depending on engine application. It is usually located in the exhaust system at the outlet of the selective catalytic reduction (SCR) catalyst.
Conditions for Running the Diagnostics
This diagnostic runs when the aftertreatment SCR outlet temperature has been above 200°C [392° F] for a calibratable period of time while the engine is running.
Conditions for Setting the Fault Codes
The Engine Control Module (ECM) detected the NOx sensor heater was unable to maintain its normal operating temperature.
Action Taken When the Fault Code is Active
- The ECM illuminates the amber CHECK ENGINE lamp and/or the malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.
Conditions for Clearing the Fault Code
- To validate the repair, use the recommended Cummins® electronic service tool or equivalent to perform the “Aftertreatment Outlet NOx Sensor Test” found in ECM Diagnostic Test.
- The fault code status displayed by the recommended Cummins® electronic service tool or equivalent will change to INACTIVE immediately after the diagnostic runs and passes.
- The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
- For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
- The “Reset All Faults” command in the recommended Cummins® electronic service tool or equivalent can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
The NOx sensor heater is internal to the NOx sensor assembly, and can not be serviced separately.
Possible causes of this fault code include:
- A damaged aftertreatment outlet NOx sensor
- Intermittent power connection to the aftertreatment outlet NOx sensor.
For intermittent power supply and datalink communication issues with Aftertreatment Components, it is highly recommended that the OEM Power Distribution Center fuses and relays be thoroughly checked for loose, missing or intermittent connections.
Troubleshooting Summary
Solution: S00000309
Verification
Conditions
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Use the recommended Cummins® electronic service tool or equivalent to read the fault codes.
Specification
Before troubleshooting this fault code, troubleshoot any fault code that is active or has more than one inactive count within the last 25 engine operating hours from the following list:
- Aftertreatment NOx: 1887, 2771, 3681
- Aftertreatment SCR: 3144, 3146, 3147, 3148
Linked Solutions
- None
Repair
- Perform a search on the appropriate fault codes.
Validation
- None
Solution: S00011171
Verification
Conditions
- Turn keyswitch OFF.
Action
- Visually inspect the batteries and the battery cable connections for corrosion.
- Measure the voltage from the positive (+) battery terminal to the negative (-) battery terminal.
- If this vehicle has been repaired within the last 30 days for the same fault code, then proceed to the Linked Solutions section.
Specification
- If the battery voltage is at least 10.8 VDC (12 volt systems) or 21.6 VDC (24 volt systems), then proceed to the Linked Solutions section.
- If the battery voltage is below 10.8 VDC (12 volt systems) or 21.6 VDC (24 volt systems), then proceed to the Repair section.
- If the battery or battery cables show signs of corrosion or damage, then proceed to the Repair Section.
Repair
Repair or replace only the components that were found to be out of specification.
- Charge or replace the batteries.
Refer to OEM Service Manual
- Clean corrosion or tighten battery cable connections.
Refer to OEM Service Manual
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the “Conditions for Clearing the Fault Code” found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00001379
Verification
Conditions
- Turn keyswitch OFF.
Action
- Disconnect the batteries from each other.
- Connect a load tester separately to each battery.
- Measure the voltage from the positive (+) battery terminal to the negative (-) battery terminal.
Specification
- For a 12 volt system, proceed to the Repair section if the battery voltage is below the following specification: 11 VDC
- For a 24 volt system, proceed to the Repair section if the battery voltage is below the following specification: 22 VDC
Linked Solutions
- None
Repair
- Charge or replace the batteries.
Refer to OEM Service Manual
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the “Conditions for Clearing the Fault Code” found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000754
Verification
Conditions
- Turn keyswitch OFF.
Action
- Visually inspect the ECM ground for damage, corrosion and loose connections.
- Visually inspect the aftertreatment interface wiring harness ground for damage, corrosion and loose connections.
- Visually inspect the OEM wiring harness ground for damage, corrosion and loose connections.
- Visually inspect the grounds for proper routing.
Specification
- If damage, corrosion or incorrect routing of grounds are found, then proceed to the Repair section
Linked Solutions
- None
Repair
- Clean or replace connections.
Refer to OEM Service Manual
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the “Conditions for Clearing the Fault Code” found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00010321
Verification
Conditions
- Reconnect previously disconnected components.
Specification
- If the Aftertreatment Outlet NOx Sensor Test does not pass, then proceed to the Repair section.
- If the Aftertreatment Outlet NOx Sensor Test does not complete, then reset the Search to Aftertreatment Outlet NOx Sensor Test did not complete.
Linked Solutions
- None
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the “Conditions for Clearing the Fault Code” found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000443
Verification
Conditions
- Connect all components.
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Use the recommended Cummins® electronic service tool or equivalent to read the fault codes.
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revision listed in the ECM calibration revision history for applicable changes.
Specification
- If a calibration update for this fault code is available, the ECM calibration revision must be that revision or higher.
Linked Solutions
- None
Repair
- Prior to downloading the ECM calibration, check to see that all job images and all other troubleshooting has been documented as downloading an ECM calibration will remove the fault codes on the ECM.
- Download the updated ECM calibration code.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the “Conditions for Clearing the Fault Code” found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
If all steps have been completed and no root cause has been identified, then follow the technical escalation process.